Contact Us Today!
Toll Free: 1-800-525-2898
Dismantling Equipment - Transmission and Engine Stacker - PDI
Back to Dismantling Equipment - Stackers
- Advanced Control Handle.
All Big Joe Power Drive Intermediate (PDI) models come equipped with the industry's most versatile control handle. Speeds may be controlled with a twist grip or thumb control. Includes 3-speed forward and reverse detent action speed control; thumb control of horn.
- "Belly-Button" Reversing Switch.
A large reversing switch, built into the control handle is designed to reverse truck direction on contact with the operator.
- Versatile Braking Systems.
Two-way mechanical linkage actuates an automotive-type disc brake when the handle is positioned in the top or bottom of its arc. "Dead-man" feature returns the handle to its upright position, cuts out travel power, and auto-mechanically engages the brake if the handle is inadvertently released.
- Electrical System.
Fully fuse protected, heavy-duty, 100 ampere industrial contactors with high current draw for three speeds forward and reverse. Modular drive control panel allows easy access of silver alloy tips for service and replacement. All wiring is coded and has quick disconnect terminals.
- Infinitely Variable, Transistorized Speed Control.
Solid-state, infinitely variable transistor speed controller utilizing a proven MOSFET power section, makes for smooth starts & stops while minimizing battery consumption. Available hand held programmer accesses fault history & runs diagnostics while allowing customization of creep speed, acceleration rate, maximum speed & plug braking settings.
- High Strength Construction.
Power section, base legs, and mast are seam-welded to form a single piece frame. This unitized construction resists operational stresses and provides a rugged housing to protect truck components.
- Industrial Rated Batteries.
Contain heavy plates and separators. Built to withstand deep-discharge and recharging. Battery compartments provide easy access to batteries for maintenance.
- Chrome Plated Lift Cylinder.
Provides smooth lift/lower performance and long seal life.
- Telescopic Mast.
Mast construction is fully-rollered, inter-locked structural steel Channel and I-Beam for strength, rigidity and long-wearing performance.
- Emergency Power Disconnect.
Externally mounted quick-release battery disconnect is readily accessible. Panel mounted with a large handle to remove all power from truck circuits in the event of an emergency.
- Battery Charger.
Internally mounted, fully automatic "smart" charger, plugs into standard 110 volt AC outlet.
- High Speed Cut-off.
Automatic cut-off circuit locks out high speed when forks are elevated above 15".
- Pressure-compensated flow control valve.
Located at base of lift cylinder, regulates lowering speed.
(other options available, consult factory)
- Adjustable Straddle Option
Available for the straddle I.D. range of 38" to 50". Adjusts in 4" increments. Will allow the truck to work with a variety of pallet sizes. Ideal if future pallet requirements may change.
- Full Free Lift
Allows fork carriage to extend to the top of the first stage before the second stage begins to extend. For lifting in areas limited by overhead clearance. Reduces lift and collapsed height 2" (consult factory).
PDI R5, R6: Rigid fork-over-straddle, non-telescopic, rated 2000# at 18" and 24" load centers.
PDI A5, A6, A7: Adjustable fork carriage, non-telescopic, rated 2000# at 18" and 24" load centers.
PDI T8, T9, Adjustable fork carriage, telescopic,
T10, T11, T12: rated 2000# at 18" and 24" load centers.
Lifting Capacity: 2,000 lbs. at both 18" and 24" load centers.
Lift Range: 5-12 ft.
Power System: 24 volt with built-in fully automatic charger.
Turning Radius: From 51"
Travel: transistor speed control
SPECIFICATIONS FOR ALL PDI MODELS
Battery: Two 12V industrial batteries connected in series, providing a 24V power source
Charger: 24V, 15 amp built-in fully automatic
- 2018 series: 24V Battery Pack (two 12V, 125 A.H.)
- 2024 series: 24V Battery Pack (two 12V, 160 A.H.)
- Compartments: Two 21" L x 75/8" W x 12" compartments
Forks: See chart
Wheel Dia: Load Wheels 4"
Drive Wheels 10"
Clearance: 11/2" floor to bottom of straddle
7/8" to stability bar under power section
Wheels: 4" Dia. x 23/4" polyurethane load wheels
(standard) 10" x 4" x 61/2" rubber, press-on, drive wheel
Back to Dismantling Equipment - Stackers